A facilities budget in Dubai can be spent in two ways. You can wait for each fault, pay for an inspection, and approve a repair when it arrives. Or you can pay in advance for planned visits that catch faults before they stop a room, a shop or a production line. The two routes look similar on a spreadsheet and behave very differently in practice, so an annual maintenance contract Dubai planners consider should be tested against the repair record first. This comparison uses the published terms of one UAE provider, Tessa Technical Services, to set out what each route costs and what it covers.
The pay-per-repair cycle
Tessa's website describes the reactive route in its own terms. One-off jobs begin with the AED 150 inspection, and the site says they are fair for a single fault but costly as a habit. An annual maintenance contract, in its framing, replaces that cycle with planned visits, so maintenance is scheduled ahead rather than booked reactively.
The principle is not specific to one company. The U.S. Department of Energy's measure guideline on air conditioner diagnostics, maintenance and replacement notes that the cost to diagnose and remediate HVAC problems varies widely with the problem found. It also notes that some faults, such as a clogged filter or a fouled condenser coil, are obvious and simple to resolve once they are identified. Read the U.S. DOE air conditioner diagnostics guide. For a planner, the lesson is that a routine check which finds a simple fault early is a different cost from a breakdown that stops a room.
What a repair record tells a planner
A call-out log is only useful if it records the cause of each fault. Tessa's AC repair page lists three usual causes when a unit runs but does not cool: a clogged filter that chokes airflow, low refrigerant from a slow leak, and a failed capacitor that stops the compressor or fan. Each of these points to a different remedy, and only some of them are the kind of fault a planned visit is meant to catch early.
The same page says that low gas always means a leak, because refrigerant is not consumed, and that topping up without repairing the leak postpones the same bill. For a facilities planner, repeated gas top-ups on one unit in the call-out record are a signal to ask for a traced leak and a complete fix quoted in writing. Tessa also gives a rule of thumb on age: a unit past 8 to 10 years that needs repeated top-ups, or has lost its compressor, is often cheaper to replace, and its technician prices both options on-site.
Tessa adds that quarterly servicing suits units that run most of the year, and that twice yearly is the workable minimum. Compare that cadence with the four visits in each plan and with the number of times the unit was actually serviced last year.
What each annual maintenance contract plan includes
Tessa publishes three annual plans with the prices stated in full:
- Basic, AED 6,000 a year. AC only, with four planned AC maintenance visits, callout inspections, and materials charged as used.
- Value, AED 9,000 a year. MEP and AC, with four planned MEP and AC maintenance visits, callout inspections, five free emergency callouts a year, and materials included up to AED 250 per visit.
- Premium, AED 12,000 a year. The full property (MEP, AC and civil), with planned maintenance for all systems and material and labour included up to AED 500 per job.
Each plan is paid 100% in advance for the year, and T&C apply, so read the terms before comparing the plans on price alone.
Each planned visit follows a documented checklist. On all plans it covers AC filters, drain lines and cooling performance. Value and Premium add plumbing checks on water heaters, pumps and visible pipework, and an electrical inspection of distribution boards and wiring points. The technician logs the findings, completes the covered work and flags developing faults.
Pay-per-repair or contract: the honest test
A contract is not automatically cheaper. Under Basic, materials are charged as used, so a property with heavy repair needs still pays for parts. Under Value, materials are included up to AED 250 per visit, and under Premium, material and labour are included up to AED 500 per job, which changes the calculation. Pay-per-repair can be the better choice when a property needs few visits.
Here is an illustrative case, not a quote. Take one office with a single AC unit that needed three separate call-outs in a year. Each call-out starts with the AED 150 inspection fee, credited to the final invoice when a written quote is approved. Whether a plan would have cost less depends on how many visits that unit would have needed anyway and how much the materials cost. Compare the last twelve months of call-out records with the plan price, and do not guess.
Who each arrangement fits
Tessa's own guidance on fit is a useful starting point for sorting a portfolio:
- Basic suits apartments where AC is the main concern.
- Value fits most villas and townhouses.
- Premium suits larger properties, offices, and landlords who want every system covered.
Tessa's website also describes a contract arrangement for landlords and property managers, with one contract per property and one report after every visit. Its FAQ states that a small apartment may only need pay-as-you-go bookings, so a contract is not automatically the right answer for every unit.
A planner's checklist
Before you choose, do three things:
- List every property and its systems: AC only, MEP and AC, or the full building.
- Pull the call-out history for the last twelve months for each property.
- Decide who signs off the visit report and where it is filed.
Then compare the plan price with the history, not with the cheapest single call-out. A plan that suits a villa may not suit an office block, so judge each property on its own record. For the planning side of the decision, the preventive maintenance guide sets out how to schedule the visits, and what a proper AC service visit includes describes the checks a planned visit should cover.
Fitting the decision to a plant or maintenance calendar
Plant managers and maintenance planners read this choice differently from a landlord. A production site already runs a maintenance calendar, with shutdown windows, shift patterns and a list of assets that cannot stop. Planned visits only help if they fit that calendar. Ask which visit dates can be agreed ahead, which areas need access outside production hours, and who on site escorts the technician.
A pay-per-repair arrangement suits a calendar with slack: an office or store room where a fault can wait a day and cost little while it waits. A contract suits the areas where a stopped unit disrupts work, because the visits are booked ahead rather than reactively. Either way, treat the plan price as one line in the maintenance budget and compare it with the logged call-outs for the same area.
Questions to put to any provider
Whichever route you choose, ask the provider to confirm in writing who receives the visit report, how covered work is recorded, and what happens to work outside the plan. Those answers matter more to a planner than the headline price, because they decide whether the record is usable when the next budget is set.
Next step
Copy the checklist into your maintenance system, and put the last twelve months of call-outs for each property into one table. Then read the plan terms on the Tessa Technical Services site before you decide.
Disclosure: this piece was not written, commissioned or reviewed by Tessa Technical Services. The company details are taken from its website. Manufax has not tested the service and does not recommend one provider over another.